🇦🇪 United Arab Emirates vs 🇾🇪 Yemen · Construction cost comparison
Cost to build: United Arab Emirates vs Yemen
Building is cheaper in Yemen. On our construction cost index Yemen sits at 24 against the United Arab Emirates at 70 (United States = 100), so the same building costs roughly 66% less to construct there. A standard 150 m² three-bedroom house runs about $147,000–$273,000 in the United Arab Emirates and $50,400–$93,600 in Yemen.
A side-by-side comparison of what it costs to build in the United Arab Emirates and Yemen — and, more usefully, why they differ. The gap is not just labour rates: the two markets measure bills to different standards, build walls to different thicknesses, found at different depths and face different code requirements. All of that is below, computed from each country's own construction conventions.
Cost, side by side
| 🇦🇪 United Arab Emirates | 🇾🇪 Yemen | |
|---|---|---|
| Construction cost index (US = 100) | 70 | 24 |
| Cost per m² (standard house) | $980 – $1,820 | $336 – $624 |
| 150 m² three-bedroom house | $147,000 – $273,000 | $50,400 – $93,600 |
| Local currency | AED (د.إ) | YER (﷼) |
Order-of-magnitude benchmarks in USD for comparability, construction cost only — excluding land, professional fees and statutory charges in both markets.
Why the two markets differ
The headline gap is labour and materials. The differences below are the ones that actually change the building — and therefore change the bill for an identical drawing.
| Factor | United Arab Emirates | Yemen |
|---|---|---|
Measurement standard Both markets measure to the same standard, so a bill prepared for one can be priced in the other with little rework — unusual and genuinely convenient. | POMI | POMI |
External wall construction Wall thickness and unit format change the masonry quantity for an identical floor plan — one of the reasons the same drawing has a different bill in each country. | 225 mm, 110/m² | 225 mm, 110/m² |
Mortar mix Richer mortar consumes more cement across the whole building — a small ratio difference is a large bill difference. | 1:5 | 1:5 |
Foundation depth Neither market is frost-governed, so depth follows bearing capacity and local convention. | 0.60 m | 0.60 m |
Seismic band Comparable seismic demand, so structural detailing is not a point of difference between them. | low | low |
Wind band Higher wind bands require tie-downs and strengthened fixings, and cyclonic zones add impact-rated glazing. | normal | high |
Insulation required Same envelope expectation in both markets. | No | No |
Foul drainage Same disposal arrangement in both, so external works is comparable on this item. | Septic tank & soakaway | Septic tank & soakaway |
Roof pitch convention Pitch converts plan area into real roof surface — a steeper convention buys more covering, timber and labour for the same footprint. | 25° | 25° |
United Arab Emirates vs Yemen — frequently asked
Is it cheaper to build in the United Arab Emirates or Yemen?
+
Building is cheaper in Yemen. On our construction cost index Yemen sits at 24 against the United Arab Emirates at 70 (United States = 100), so the same building costs roughly 66% less to construct there. A standard 150 m² three-bedroom house runs about $147,000–$273,000 in the United Arab Emirates and $50,400–$93,600 in Yemen.
What is the cost per square metre in each?
+
About $980–$1,820 per m² in the United Arab Emirates and $336–$624 per m² in Yemen, for a standard-specification single-storey house. Rates rise with storey height and specification in both markets.
Why is there a difference at all?
+
Three things dominate: labour cost, how much of the material basket has to be imported, and what the building code requires. Here both markets have similar envelope requirements, so the gap is driven mainly by labour and materials.
Can I use the same drawings in both countries?
+
The bill can carry across with little rework since both use POMI, but the design still has to satisfy each country's own code — foundations, seismic and wind requirements differ regardless of the measurement standard.
How do I get a real figure rather than a benchmark?
+
Upload your dimensioned floor plans and generate a measured bill of quantities for whichever market you are building in — priced in AED or YER, in that country's own measurement standard, with every rate source-cited.