🇵🇾 Paraguay · Cómputos Métricos y Presupuesto de Obra · Work section
Joinery, doors & windows in a Paraguay bill of quantities
In Paraguay, the joinery section of a Bill of Quantities (Cómputos Métricos y Presupuesto) (Cómputos Métricos y Presupuesto de Obra) is measured to Cómputos Métricos y Presupuesto de Obra (Latin American practice). It covers 6 principal groups of work — door frames, linings and door leaves through to staircases and balustrades — and is headed in the bill as "CAPÍTULO 03 — JOINERY, DOORS & WINDOWS".
Joinery, doors & windows is one of the sections every Bill of Quantities (Cómputos Métricos y Presupuesto) (Cómputos Métricos y Presupuesto de Obra) in Paraguay is built from. This page sets out what belongs in it, the unit each item is measured in under Cómputos Métricos y Presupuesto de Obra (Latin American practice), the local conventions that change the quantities here, and a worked example for a 150 m² house — plus the errors in this section that actually cost money on site.
What this section covers
- Door frames, linings and door leaves
- Window frames and glazing
- Ironmongery — hinges, locks, handles, closers
- Fitted kitchen units and worktops
- Built-in wardrobes and shelving
- Staircases and balustrades
How each item is measured
| Item | Unit | Measurement rule |
|---|---|---|
| Doors and frames | no. | Enumerated by type, stating size, material, finish and handing. Priced against a door schedule, not a count. |
| Windows | no. or m² | Enumerated by type or measured on the opening area, stating glazing and opening arrangement. |
| Ironmongery | no. or set | Enumerated per door, by set. Easily 10–15% of the joinery section on a house. |
| Kitchen units | no. or m | Enumerated by unit type, or measured on the run length, stating the specification. |
| Staircase | item | A single lump sum item, fully described — flights, landings, balustrade and finish. |
Local conventions in Paraguay
- —Standard door size here is 900 × 2100 mm; standard window 1500 × 1200 mm, with bathroom windows around 600 × 600 mm.
- —A house of typical size here carries roughly one door per 12 m² and one window per 14 m² of floor area — a useful check against the schedule.
- —Non-standard sizes are made to order and cost disproportionately more than the size difference suggests.
Worked example — 150 m² house in Paraguay
Quantities for this section on a representative single-storey house, computed from Paraguay construction conventions. Rates are deliberately not shown: they move constantly and are priced against your own drawings.
| Description | Qty | Unit |
|---|---|---|
Doors ~1 per 12 m² of floor area | 13 | no. |
Windows ~1 per 14 m² of floor area | 11 | no. |
Lighting points 0.12/m² | 18 | no. |
Socket outlets 0.18/m² | 27 | no. |
WC suites Typical fixture count per dwelling | 2 | no. |
Wash hand basins Typical fixture count per dwelling | 2 | no. |
Septic tank & soakaway Municipal sewer is not generally available; on-site treatment assumed | 1 | item |
What goes wrong in this section
- —Ironmongery is specified vaguely and priced cheaply, then upgraded on site at full retail. Schedule it properly at bill stage.
- —Joinery lead times routinely exceed the masonry programme. A late frame order holds up plastering and therefore everything after it.
- —Enumerate from a schedule, never from an area rule, whenever a drawing exists — this is the one section where estimating from floor area is indefensible.
Get every section measured, not just this one
Upload your dimensioned drawings and get a complete bill of quantities (cómputos métricos y presupuesto) in the Cómputos Métricos y Presupuesto de Obra format, priced in PYG (Gs), with every rate source-cited.
Generate my Paraguay BoQJoinery, doors & windows — frequently asked
What goes into the joinery section of a bill of quantities in Paraguay?
+
Door frames, linings and door leaves; Window frames and glazing; Ironmongery — hinges, locks, handles, closers; Fitted kitchen units and worktops; and 2 further groups of work. Under Cómputos Métricos y Presupuesto de Obra each is described, measured in its own unit, and priced separately so the total is auditable line by line.
What units is joinery, doors & windows measured in?
+
Doors and frames in no., Windows in no. or m², Ironmongery in no. or set, Kitchen units in no. or m. Getting the unit right matters more than getting the quantity precisely right — a contractor can adjust a quantity, but cannot price an item measured in the wrong unit at all.
How is joinery, doors & windows different in Paraguay from elsewhere?
+
Standard door size here is 900 × 2100 mm; standard window 1500 × 1200 mm, with bathroom windows around 600 × 600 mm.
What is the most common costly mistake in this section?
+
Ironmongery is specified vaguely and priced cheaply, then upgraded on site at full retail. Schedule it properly at bill stage.
How do I get this section measured for my own project?
+
Upload your dimensioned drawings to Enormous Buildings. The bill is produced in the Cómputos Métricos y Presupuesto de Obra format, grouped by section with joinery, doors & windows priced in PYG (Gs), and every unit rate carries a source so a Paraguay quantity surveyor can check it.